Oregon Lightning Load Pro Tap & Go Head 130 mm
Oregon's 130 mm Lightning Load Pro: loads in 30 seconds without disassembly, takes line up to 4 mm, five adaptors including M12 sizes.
In short:The Oregon Lightning Load Pro 130 mm is a large tap-and-go head for brush cutters over 33 cc. It loads line in 30 seconds or less without disassembly, takes line up to 4 mm of various shapes, has shaped steel bushings to reduce breakage and comes with Oregon Techni 280 line. Five adaptors are included: M8 × 1.25 LH male, M10 × 1, M10 × 1.25, M12 × 1.5 and M12 × 1.75 LH female. It suits powerful petrol machines.
You'll be sent to Amazon in your country. Indicative price — live, localised pricing where available. As an Amazon Associate we earn from qualifying purchases.
Pros
- Takes thick line up to 4 mm
- Reloads in 30 seconds without opening
- Five adaptors, including M12 sizes
Cons
- Only for larger machines (33 cc+)
- Big head adds weight at the end of the shaft
What it is
The large, 130 mm version of Oregon’s Lightning Load Pro tap-and-go head, for brush cutters over 33 cc. Oregon says it loads line in 30 seconds or less with no need to disassemble the head, takes line up to 4 mm of various shapes, and has shaped steel bushings at the exits to avoid line breakage. It comes with Oregon Techni 280 line. It was sold by Amazon when we checked in October 2026.
Adaptors
Five adaptors are included, plus nuts and bolts: M8 × 1.25 LH (male), M10 × 1, M10 × 1.25, M12 × 1.5 and M12 × 1.75 LH (female). The M12 options make it one of the few quick-load heads for larger machines with M12 arbors; the smaller 109 mm Lightning Load Pro covers M8 and M10 only.
Will your machine drive it?
A 130 mm head with 3–4 mm line needs a powerful petrol engine: on a mid-size machine it overloads the clutch and slows the line below cutting speed. Check your manual’s line and head limits and our line size guide.
Using it
Tap the head on the ground at full throttle to release line. To reload, align the head, push line through until the ends are equal and twist. Compare heads in the best brush cutter heads.
More heads we cover
A cheap pattern bump-feed head replacing the Echo Speed-Feed 400 on the SRM-210, SRM-225 and SRM-230 — tap-to-feed, no special tools.
- TypeBump feed (tap to release line)
- ReplacesEcho Speed-Feed 400
- Listed forEcho SRM-210, SRM-225, SRM-230
Husqvarna's T25 tap-and-go trimmer head with a 10 mm left-hand thread — the standard head on many Husqvarna straight-shaft trimmers.
- TypeTap-and-go (bump feed), twin line
- Arbor10 mm, left-hand thread
- ShaftStraight-shaft machines
Husqvarna's T35 semi-automatic (tap) trimmer head for 2.4–2.7 mm line — a tougher head for mid-size petrol brush cutters on rough grass.
- TypeSemi-automatic (tap) head
- Line size2.4–2.7 mm
- Part number578 44 63-01
A twin-line tap-feed trimmer head with an M10 × 1.25 left-hand thread, pre-loaded with 4 m of 2.4 mm line and cutting up to 30 cm — for petrol brush cutters.
- TypeTwin-line tap (bump) feed head
- ThreadM10 × 1.25 left-hand
- Line supplied4 m of 2.4 mm, pre-loaded