LADAMI Tap & Go Universal Head (M10 × 1.25)
A tap-and-go twin-line head that loads without disassembly, with aluminium line exits and adaptors for M8 × 1.25 LH, M10 × 1.25 LH, M10 × 1 LH and 3/8-24 RH.
In short:The LADAMI head is a universal tap-and-go twin-line trimmer head for petrol brush cutters. You load line through the head without taking it apart, the line exits are aluminium to stop kinking, and the body is impact-resistant nylon. It comes with adaptors for M8 × 1.25 left-hand male, M10 × 1.25 left-hand female, M10 × 1 left-hand female and 3/8-24 right-hand threads, and is rated to 10,000 rpm. Check your arbor matches before buying.
You'll be sent to Amazon in your country. Indicative price — live, localised pricing where available. As an Amazon Associate we earn from qualifying purchases.
Pros
- Loads without opening the head
- Four adaptors cover most petrol machines
- Aluminium exits resist line wear
Cons
- Pattern part — budget build
- Maximum line size isn't stated
- Couldn't be dispatched to us in October 2026
What it is
A universal tap-and-go twin-line head from LADAMI. The listing describes loading without disassembly (feed the line straight through the head), aluminium line exits that stop the line kinking, an impact-resistant nylon body, and a rating of up to 10,000 rpm. Adaptors are supplied for M8 × 1.25 LH (male), M10 × 1.25 LH (female), M10 × 1 LH (female) and 3/8-24 RH. This page’s address mentions 3 mm line; the listing doesn’t state a maximum line size. When we checked in October 2026, it couldn’t be dispatched to our location.
Will it fit?
Check your gearbox thread against the four adaptors. Many European petrol brush cutters use M10 × 1.25 left-hand, which is covered. Line size is the other question: use what your machine’s manual recommends — our line size guide explains how.
Using it
Tap the head on the ground at full throttle to release line. To reload, line up the head, push a length of line through until the ends are equal and twist to wind it in. If line won’t release, see line won’t feed.
Alternatives
A branded quick-load head with known line capacity, such as the Oregon Lightning Load Pro (up to 3 mm), costs more but is better documented. Compare in the best brush cutter heads.
More heads we cover
A cheap pattern bump-feed head replacing the Echo Speed-Feed 400 on the SRM-210, SRM-225 and SRM-230 — tap-to-feed, no special tools.
- TypeBump feed (tap to release line)
- ReplacesEcho Speed-Feed 400
- Listed forEcho SRM-210, SRM-225, SRM-230
Husqvarna's T25 tap-and-go trimmer head with a 10 mm left-hand thread — the standard head on many Husqvarna straight-shaft trimmers.
- TypeTap-and-go (bump feed), twin line
- Arbor10 mm, left-hand thread
- ShaftStraight-shaft machines
Husqvarna's T35 semi-automatic (tap) trimmer head for 2.4–2.7 mm line — a tougher head for mid-size petrol brush cutters on rough grass.
- TypeSemi-automatic (tap) head
- Line size2.4–2.7 mm
- Part number578 44 63-01
A twin-line tap-feed trimmer head with an M10 × 1.25 left-hand thread, pre-loaded with 4 m of 2.4 mm line and cutting up to 30 cm — for petrol brush cutters.
- TypeTwin-line tap (bump) feed head
- ThreadM10 × 1.25 left-hand
- Line supplied4 m of 2.4 mm, pre-loaded